CHAMBERLAIN WHISPER DRIVE 2. OWNER'S MANUAL Pdf Download. Periodic checks of the opener are required to ensure safe operation. The model number label is located on the left side panel of your opener.

The Chamberlain Group, Inc. Larch Avenue Elmhurst, Illinois 6. INTRODUCTION Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual.

To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. ONLY operate garage door opener at 1. V, 6. 0 Hz to avoid malfunction and damage. Tools needed During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below. Planning Identify the type and height of your garage door.

Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener. Planning (Continued) ONE- PIECE DOOR INSTALLATIONS • Generally, a one- piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 1.

Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 1. Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below.

Download the free trial version below to get started. Double-click the downloaded file to install the software.

Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. SECURITY✚ 3- Button Remote Control (2)Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. Spring/Trolley Nut (1) Bolt 1/4"- 2. Trolley Threaded Shaft (1) Carriage Bolt Wing Nut 1/4"- 2. Lag Screw 5/1. 6"- 9x. Lag Screw 5/1. 6"- 1.

C B A Whisper 20 Ultra. See our price list / catalog for all built-in parts or surf to www.mastervoltusa.com Whisper 20 kVA Ultra, with the service side open.

Please Disable Your Ad-blocker Safe and free downloads are made possible with the help of advertising and user donations. Please disable your ad-blocker. "Careless Whisper" is a song by English singer-songwriter George Michael (sometimes credited to "Wham! featuring George Michael" in Japan, Canada and the United States). Free mixtape download for Reggalatorz - Reggae & Relaxation. Click listen button to stream. Register for free to download this mixtape and others. · Free Download Whisper32 1.16 - Whisper32 is a very easy-to-use Password Manager for Windows.

ASSEMBLY STEP 1 Assemble the Rail & Install the Trolley To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end (see illustration). The hole above this window is larger on the top of the rail than on the bottom.• Insert a 1/4"- 2. Tighten securely with a 1/4"- 2.

Idler Bolt To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener. U" Bracket Bolt.. To avoid possible SERIOUS INJURY to fingers from moving garage door opener: • ALWAYS keep hand clear of sprocket while operating opener. Securely attach sprocket cover BEFORE operating. Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to avoid entanglement.

Install garage door opener 7 feet (2. Mount emergency release handle 6 feet (1. INSTALLATION STEP 1 Determine the Header Bracket Location WARNING To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to structural CAUTION support on header wall or ceiling, otherwise garage door might not reverse when required.

DO NOT install header bracket over drywall. INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.

If installing into masonry, use concrete anchors (not provided). INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re- use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated.

Do not position the opener more than 4" (1. CAUTION To prevent damage to garage door, rest garage door opener rail on 2x. Rail 2x. 4 is used to determine.. INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener.

CAUTION INSTALLATION STEP 6 Install the Door Control Locate door control within sight of door at a minimum height of 5 feet (1. The installation surface must be smooth and flat.

If installing into drywall (Figure 1), drill 5/3. Then the lights will turn OFF. Reverse the procedure to close the lens. Use A1. 9, standard neck garage door opener bulbs for replacement. NOTE: Use only standard light bulbs. The use of short neck or speciality light bulbs may overheat the endpanel or light socket. WARNING INSTALLATION STEP 9 Electrical Requirements CAUTION To avoid installation difficulties, do not run the opener at this time.

To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.

If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. Facing the door from inside the garage ® Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. To prevent SERIOUS INJURY or DEATH from a closing garage door: •.. INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (1.

They may be installed in one of three ways, as follows. MOUNTING AND WIRING THE SAFETY REVERSING SENSORS • Slide a 1/4"- 2. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5). INSTALLATION STEP 1.

Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two or three vertical supports. A vertical reinforcement brace should cover the height of the top panel. ONE- PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page.

They apply to one- piece doors also. Center the door bracket on the top of the door, in line with the header bracket as shown.

Mark either the left and right, or the top and bottom holes. INSTALLATION STEP 1. Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page.

SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Download Free Kung Fu Games For Pc. ALL ONE- PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). With the door closed, connect the straight door arm section to the door bracket with the 5/1. ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar.

Run the opener through a complete travel cycle. ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the right panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door.

If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. The door will not move more than an inch (2. The garage door opener will not close from a remote if the indicator light in either sensor is off (alerting you to the fact that the sensor is misaligned or obstructed).• The wall- mounted Door Control: Hold the push button or bar down until the door starts to move.